Guide
How to Change a Euro Cylinder Lock, Step by Step
With the door open and a working key, a euro cylinder comes out in minutes: undo the long retaining screw in the door edge, turn the key slightly so the cam lines up with the body, and slide the cylinder out. Fit a TS 007 3 star or SS 312 Diamond replacement of the same size. A locksmith charges £105 to £175 fitted (MLA, MyJobQuote).
Can you change your own euro cylinder?
Yes, in most cases, if you own the home and have a key that works. The cylinder is a separate part held in by one screw, which is why it is the part people change after moving house or losing a key.
Three things to settle first:
- You need a working key and an open door. The cam in the middle of the cylinder has to be turned into line before it will slide out, and that takes the key. Without one, getting the cylinder out means destroying it, which is a locksmith's job.
- If you rent, check your tenancy agreement. Many allow a change only with the landlord's agreement, and you will usually need to give the landlord a key. The guide on whether a tenant can change the locks covers this.
- Check your home insurance wording. If the policy names a standard for the cylinder, the replacement has to meet it.
What do you need?
Very little:
- the replacement cylinder, in the right size and grade;
- a screwdriver that fits the retaining screw, usually a long cross-head;
- a tape measure or ruler;
- the working key for the old cylinder;
- something to wedge the door open.
Order the new cylinder after measuring the old one, not before. Cylinders are sold as two measurements, outside and inside, taken from the centre of the fixing screw. A cylinder that is too long leaves the barrel standing proud of the handle on the outside, which makes it easier to attack; one that is too short may not let the cam turn. The euro cylinder guide explains sizes in more detail.
How do you change a euro cylinder?
Keep the door open throughout, so you cannot lock yourself out halfway:
- Find the retaining screw. It is on the edge of the door, in the faceplate, in line with the cylinder and usually below the handle spindle. Undo it fully and put it somewhere safe.
- Line up the cam. Put the key in and turn it slightly, about 10 to 15 degrees either way from upright, until the cam tucks inside the cylinder body. You will feel the cylinder loosen.
- Slide it out. Holding the key in that position, pull gently and the cylinder slides out of the door. A little wiggle of the key helps if the cam catches.
- Fit the new one. Put its key in, set the cam in the same tucked position, and slide it in from the outside so the screw hole lines up with the faceplate.
- Refit the screw by hand first, then tighten it firmly without forcing.
- Test with the door open. Lock and unlock from both sides with each new key, and lift the handle to check the bolts and hooks move freely. Only then close the door and test again.
What can go wrong?
Most problems have a simple cause:
- The cylinder will not come out. The cam is not tucked in. Turn the key a little the other way and try again, without pulling hard.
- The retaining screw will not turn. It may be painted over or corroded. Clean out the head before it rounds off.
- The new cylinder is stiff once fitted. The retaining screw may be too tight, or the cylinder is the wrong length and the cam is binding. Check the sizes.
- The door still will not lock easily. The cylinder was not the problem. A uPVC door that needs a hard lift has usually dropped, or its gearbox is worn, and a new cylinder does not cure either.
If a door that locked before does not lock after the change, refit the old cylinder while you work out why, so the house is not left insecure.
Which cylinder should you buy, and when should you call a locksmith?
Buy a graded cylinder. Secured by Design describes BS 3621 as the minimum standard for locks on external doors, and for euro cylinders it points to TS 007, which builds on BS EN 1303 and BS 3621's vulnerability assessment, and to Sold Secure's SS 312. In practice look for one of these on the cylinder face:
- TS 007 3 star, which resists snapping on its own;
- TS 007 1 star with a 2 star handle, the same protection shared between the two parts;
- Sold Secure SS 312 Diamond.
Prices from the guides this site uses:
| Item | Typical price | Source |
|---|---|---|
| Anti-snap cylinder, parts only | from £64 | MLA, 2026 |
| Anti-snap cylinder, fitted | from £137 (Checkatrade average about £150) | MLA, Checkatrade |
| Euro cylinder change, fitted | £105 to £175 | MLA, MyJobQuote |
Call a locksmith if you have no working key, the door is locked shut, the cylinder has been attacked, the door has several cylinders you want on one key, or you want a restricted key system where copies need a registration card.
Common questions
How long does it take to change a euro cylinder?
A straightforward swap takes a few minutes once you have the right cylinder. Measuring, buying and testing take longer than the change itself.
Can I change a euro cylinder without the key?
Not without damaging it, because the key turns the cam into line so the cylinder can slide out. With no key, call a locksmith.
Do I need to change the handle as well?
Not with a TS 007 3 star or SS 312 Diamond cylinder. A 1 star cylinder needs a 2 star handle to reach the same rating. Replace the handle anyway if it is loose or drooping.
Will the new cylinder come with keys?
Yes, usually three or more. Restricted cylinders also come with a card you need for extra keys, so store it somewhere safe and away from the keys.