Guide
Broken Key in the Lock? How to Get a Snapped Key Out
If part of the broken key sticks out, grip it with fine pliers and draw it straight out without twisting. If it is flush with the lock or deeper, stop: digging pushes it further in and can damage the pins. A locksmith usually has a snapped key out within half an hour, and the MLA puts a typical job at about £85.
What should you do first when a key snaps?
Stop turning. The piece left in the lock is now holding the cylinder in whatever position it reached, and every attempt to turn it with the stub or a screwdriver can bend the pins inside.
Then work out where you stand:
- Is the door open or shut? If it is open, you have time. Keep it from closing.
- Is it locked? If you are outside a locked door with no other key, this is a lockout, and the guide to being locked out of your house covers the free options before you pay anyone.
- Is there a spare key? It will not help while the broken piece is in the lock, but it saves cutting a new one later.
Keep both halves of the broken key. A clean break is often enough for a new key to be cut.
Can you get a broken key out yourself?
Sometimes, if enough of the key sticks out to grip:
- Turn the cylinder back to the upright position the key went in at, if it moved. A key can usually only come out in that position.
- Grip the exposed end with fine needle-nose pliers or tweezers.
- Draw it straight out, slowly, without twisting or rocking.
If the piece is flush with the face of the lock or below it, the Master Locksmiths Association's advice is not to try. It says removing a broken key yourself can damage the lock's internal parts and push the piece further in, which makes the locksmith's job longer.
Two popular tricks cause the most damage. Superglue on a matchstick or wire can run into the pins and seize them, turning a simple removal into a new lock. Drilling or poking the fragment deeper does the same. A lock that would have survived the removal often does not survive these.
Why do keys snap in locks?
A key rarely breaks without a reason, and the reason usually needs fixing too:
- The key was worn or cracked. Old keys thin at the neck, where the blade meets the bow, and that is where they break.
- It was a copy of a copy. Each copy loses a little accuracy, so it binds in the lock.
- The lock was stiff. A dropped uPVC door, a dry cylinder or a bolt pressing on its keep all make people force the key.
- The key was used as a handle, to pull the door shut or lift it into line.
If the lock was stiff before the key broke, the guide to a key stuck in the lock covers the causes, and the uPVC door guide covers a door that has dropped.
How does a locksmith remove a broken key, and what does it cost?
A locksmith uses thin extractor tools that slide alongside the broken blade, catch its cuts and draw it out. The MLA says a key that has just broken in a working lock should take no longer than half an hour to remove, and puts a typical half-hour job at about £85, more in London and in rural areas where travel takes longer.
Sometimes the cheaper answer is a new cylinder, for example when the lock is already failing or the piece has been pushed deep. Typical prices for comparison:
| Work | Typical price | Source |
|---|---|---|
| Broken key removal, simple job | about £85 | MLA |
| Euro cylinder replaced, fitted | £105 to £175 | MLA, MyJobQuote |
| Out-of-hours surcharge | £50 to £100 on top | MyJobQuote |
On the phone, say what kind of lock it is, whether the door is locked, and how much of the key is showing. Ask for the total and whether replacing the cylinder is likely.
Do you need a new lock, or just a new key?
Usually just a key. The MLA says a new key can be cut from the broken pieces if the break is clean and the two halves fit together. If the key is too damaged to copy, a locksmith can make one to fit the lock itself.
A standard cylinder or Yale-type key costs about £4 to £7 to cut (Home Secure Shop; MLA from £5.55), and a security or restricted key from £21.15 on the MLA's 2026 list, ordered against its registration card.
Replace the lock as well if it was stiff before the key broke, if the removal damaged it, or if the key belongs to a lock you were already thinking of upgrading. Otherwise, have the new key cut from the original pattern or code, not from another worn copy, so the same thing does not happen again.
Common questions
Will the locksmith need to drill the lock?
Rarely for a simple break in a working lock; extractor tools usually do it. If the lock is damaged or the piece has been forced deep, replacing the cylinder may be quicker and cheaper. Ask before any drilling starts.
Can I lock the door with part of a key stuck in it?
Usually not, because the broken piece stops the cylinder turning properly. If the door has to be secured tonight, call a locksmith rather than forcing it.
Can a key cutter copy a snapped key?
Often, yes, if the break is clean and the two pieces line up. Take both halves. If the cuts near the break are damaged, a locksmith can cut to the lock instead.
Does home insurance pay for a broken key?
Some home emergency covers include it; standard policies often do not. Check the wording or ring the insurer before booking, because they may want to send their own locksmith.