Guide
Key Stuck in the Lock? How to Get It Out Without Damage
A key that will not turn or come out is usually out of line, worn, or held by a door that has moved. Return it to the upright position it went in at, take the pressure off the door, and ease it while wiggling gently; never lever it. If it stays stuck, the MLA puts a locksmith's removal from £85, and most take under 20 minutes.
Why is my key stuck in the lock?
The Master Locksmiths Association lists four usual causes: the lock is failing, the key is badly cut, worn or broken, the lock is being operated the wrong way, or it is simply the wrong key. To those add the door itself. When a uPVC door drops or a timber door swells, the bolt or hooks press on their keeps, and that pressure travels back into the cylinder and grips the key.
Dirt and dryness play a part too. A cylinder that has never been lubricated, or has been oiled with something that gathers grit, gets harder to turn each year until one day the key will not come back. A key that has started to need a jiggle is the early warning, and the cheapest point to deal with it.
Key stuck and will not come out: what to try
Go gently, and stop if the key starts to bend:
- Turn it back to upright. In most cylinders the key can only be withdrawn in the position it went in at. A few degrees off and it will not come out.
- Push it fully in, then try again. A key half out catches on the pins.
- Take the load off the door. Push the door towards the frame, or pull it towards you, while easing the key. On a uPVC door, lift the handle slightly as well.
- Wiggle up and down, not side to side, while drawing it out slowly.
Do not grip the key with pliers and twist. A key that snaps leaves a harder job behind it; the guide to a key snapped in the lock covers that. And as the MLA puts it, do not take the lock apart yourself.
Key will not turn: the common causes
A key that goes in but will not turn usually tells you what is wrong by how it behaves:
| What happens | Likely cause | First check |
|---|---|---|
| Turns from inside, not from outside | Door out of line, or the cylinder cam is worn | Try with the door open |
| Turns part way then stops | Bolt or hooks pressing on the keep | Push or lift the door while turning |
| New copy will not turn, original does | Badly cut copy | Have it recut from the original |
| Stiff whatever you do | Dry or worn cylinder | Try the spare key |
| Turns, but the door will not open | Gearbox or latch failure | See below |
If the key turns freely when the door is open but sticks when it is shut, the lock is fine and the door has moved. The guide to a dropped uPVC door explains the adjustment.
What if the key turns but the door will not open?
That means the key is turning the cylinder but nothing is reaching the bolt or latch. On a uPVC door, the usual cause is a broken gearbox in the multipoint mechanism: the key and handle move, but the hooks stay locked. On a night latch or mortice lock, a broken spring or cam inside the lock does the same.
These are not faults you can fix from outside, and a door stuck locked is a lockout. Call a locksmith, say exactly what the key and handle do, and ask whether they expect to open it without damage. A gearbox repair starts at £85 on the MLA's 2026 list, and a full multipoint mechanism is about £175 fitted (MyJobQuote).
Which lubricant should you use, and what will a locksmith charge?
On lubricants, the MLA's advice splits by lock. For pin-tumbler cylinders, graphite is the conventional choice and oil is not recommended. For uPVC multipoint mechanisms, it advises against ordinary WD-40 and recommends a PTFE lubricant that will not attract dirt. Apply it to a key-free lock, then work the key in and out a few times.
If the key stays stuck, the MLA prices removal from £85, says most jobs take less than 20 minutes, and notes that travel can add to the bill. If the cylinder is worn out, replacing it costs £105 to £175 fitted (MLA, MyJobQuote), or from £137 for an anti-snap grade. Out of hours, MyJobQuote adds £50 to £100. Ask for the total on the phone, including the new cylinder if one is likely.
Common questions
Should I use WD-40 on a sticking lock?
The MLA advises against ordinary WD-40 for uPVC mechanisms, preferring a PTFE lubricant, and suggests graphite rather than oil for pin-tumbler cylinders.
Is it safe to leave a key stuck in the door overnight?
Not on the outside of a door. Anyone could turn it. If it will not come out and the door cannot be locked another way, call a locksmith that day.
Will a stuck key mean a new lock?
Often not. If the key is worn or the door has dropped, a new key or an adjustment fixes it. A cylinder worn inside is replaced, which is a quick job.
Why does my key only stick in cold or hot weather?
Doors move with temperature, especially uPVC. If the key sticks only in some weather, the door is only just in line and a small adjustment usually cures it.